Home / GATE 2017-2018 / GATE Mechanical :: Practice Test Paper 1

GATE 2017-2018 :: GATE Mechanical

  1. In abrasive jet machining, as the distance between the nozzle tip and the work surface increases, the material removal rate
  2. A.
    increases continuously.
    B.
    decreases continuously.
    C.
    decreases, becomes stable and then increases.
    D.
    increases, becomes stable and then decreases.

  3. Match the following metal forming processes with their associated stresses in the workpiece.
    Metal forming process      Type of stress
    1. Coining                             P. Tensile
    2. Wire Drawing                  Q. Shear
    3. Blanking         R. Tensile and compressive
    4. Deep Drawing   S. Compressive
  4. A.
    1-S, 2-P, 3-Q, 4-R
    B.
    1-S, 2-P, 3-R, 4-Q
    C.
    1-P, 2-Q, 3-S, 4-R
    D.
    1-P, 2-R, 3-Q, 4-S

  5. In an interchangeable assembly, shafts of size  mate with holes of size  The maximum interference (in microns) in the assembly is
  6. A.
    40
    B.
    30
    C.
    20
    D.
    10

  7. During normalizing process of steel, the specimen is heated
  8. A.
    between the upper and lower critical temperature and cooled in still air.
    B.
    above the upper critical temperature and cooled in furnace.
    C.
    above the upper critical temperature and cooled in still air.
    D.
    between the upper and lower critical temperature and cooled in furnace.

  9. Oil flows through a 200 mm diameter horizontal cast iron pipe (friction factor, f = 0.0225) of length 500 m. The volumetric flow rate is 0.2 m3/s. The head loss (in m) due to friction is (assume g = 9.81 m/s2)
  10. A.
    116.18
    B.
    0.116
    C.
    18.22
    D.
    232.36

  11. For an opaque surface, the absorptivity (α) , transmissivity (t) and reflectivity (ρ) are related by the equation:
  12. A.
    α + ρ = t
    B.
    α + ρ + t = 0
    C.
    α + ρ = 1
    D.
    α + ρ = 0

  13. Steam enters an adiabatic turbine operating at steady state with an enthalpy of 3251.0 kJ/kg and leaves as a saturated mixture at 15 kPa with quality (dryness fraction) 0.9. The enthalpies of the saturated liquid and vapor at 15 kPa are hf = 225.94 kJ/kg and hg = 2598.3 kJ/kg respectively. The mass flow rate of steam is 10 kg/s. Kinetic and potential energy changes are negligible. The power output of the turbine in MW is
  14. A.
    6.5
    B.
    8.9
    C.
    9.1
    D.
    27.0

  15. The following are the data for two crossed helical gears used for speed reduction: 
    Gear I : Pitch circle diameter in the plane of rotation 80 mm and helix angle 30o 
    Gear II : Pitch circle diameter in the plane of rotation 120 mm and helix angle 22.5o 
    If the input speed is 1440 rpm, the output speed in rpm is
  16. A.
    1200
    B.
    900
    C.
    875
    D.
    720

  17. A solid disc of radius r rolls without slipping on a horizontal floor with angular velocity ω and angular acceleration α. The magnitude of the acceleration of the point of contact on the disc is
  18. A.
    zero
    B.
    rα
    C.
    √(rα)2 + (rw2)2
    D.
    rw2

  19. The area enclosed between the straight line y = x and the parabola y = x2 in the x-y plane is
  20. A.
    1/6
    B.
    1/4
    C.
    1/3
    D.
    1/2